Notre site Internet utilise des cookies pour garantir que nous vous donnons la meilleure expérience d'utilisateur. En continuant de parcourir notre site, vous êtes d'accord avec l'utilisation de cookie. plus d'infos

fermer Close Cookie Notification
Instron
  • Back
  • Home
  • Produits
    SYSTÈMES D’ESSAI
    Systèmes d’essai universels
    Essai d’endurance de structures
    Machines d’essai robotisées
    Systèmes d’essais dynamiques et de fatigue
    Simulation de crash
    Bancs d’essai de torsion
    Rhéomètres et plastomètres
    Puits de chute et moutons pendules
    HDT & Vicat
    Plus en production
    ACCESSOIRES
    Logiciel
    Mâchoires de traction
    Pelage, friction, perforation
    Chambres de température et fours
    Capteurs de force
    Bancs de flexion
    Plateaux de compression
    Dispositifs pour essais pharmaceutiques et biomédicales
    Extensomètres
    Capteurs de force
    Outillages microélectroniques
    Mesure et préparation d’échantillon
    Tous les accessoires
    Catalogue d’accessoires
  • Solutions industrielles
    PAR MATÉRIAU PAR NORME PAR TYPE D’ESSAI
    PAR SECTEUR
    Aéronautique et spatial
    Automobile
    Biomédical
    Électronique
    PAR SECTEUR
    Automobile
    Biomédical
    Électronique
  • Services et assistance
    Instron Connect CYCLE DE VIE DU PRODUIT
    FORMATION
    Bluehill
    Formation sur site dans votre établissement
    Apprentissage en ligne
    Bonnes Pratiques des Essais des Matériaux
    SERVICES
    Étalonnage et vérification
    Aide à la mise en œuvre
    Maintenance préventive
    Installation et déménagement
    Réparation et remise à neuf
    Mises à jour
    SUPPORT TECHNIQUE
    FAQ
    Services de mise à jour de logiciels
    RESSOURCES
    Manuels
    Localisateur de numéro de série
  • Notre société
    CARRIÈRES SALLE DE PRESSE ABONNEZ-VOUS À NOS LETTRES D’INFORMATION
    À PROPOS DE NOUS
    Notre histoire
    Nos implantations
    Accréditations et certificats
    RESSOURCES
    Glossaire
    Types d’essai
    Bibliothèque
    Lettres d’information
    Nouvelles
    Événements
    Séminaires en ligne
    Étude de cas
  • Nous contacter
  • France
Produits » Accessoires d'essai » Frame Accessories » Protective Shields » Debris Shield, Table Mounted Systems

Debris Shield for Table Mounted Testing Machines

Load Frame Accessories

  • Protective Shields
Contactez-nousDemander un catalogue accessoires
Protective shields for specimen testing
Protective shields for specimen testing
  • Protective shields for specimen testing
  • Protective shields for specimen testing
  • Description
  • Specifications
  • Literature

2910 074 | Debris Shield for Table Mounted Testing Machines

Consists of a 1000 mm (39.4 in) high polycarbonate panel in an aluminum frame, mounted to the column cover T-slots with hinges.

Working height is adjustable.

Compatible with Instron interlock kits.

Use with Model 336X (dual T-slot column cover style only), 446X*, 556X, 586X, and 596X dual column table top, standard width load frames only.

Clearance between center of load string and panel:

  • 175 mm (6.8 in) on 336X
  • 181 mm (7.0 in) on 446X, 556X, 586X and 596X

Mounting to the rear of the frame above the motor housing leaves an unprotected gap of 224 mm (8.8 in).

IMPORTANT NOTE: It is essential and often required by regulations that users perform their own risk assessment based on their particular application(s). Instron can assist users in conducting a risk assessment. Most applications do not require a guard. The non-interlocked Debris Shield may be appropriate in low risk applications for protection against non-hazardous debris such as dust, fibers or heat treat scales.

If your risk assessment indicates that the breakup of your specimens may create hazardous projectiles, or if crush hazards exist when inserting very short specimens by hand, then an Interlocked Guard should be used for compliance with international regulations and directives.

If your risk assessment shows that a hazard exists from dangerous projectiles ejecting toward the rear of the machine, then a rear guard may be required.

*Use with 446X frames requires moving the 4400 Control Panel mounting to the right side column cover.

**Not for use with AVE/SVE

Hauteur 1000 mm (39.4 in)
Largeur 568 mm (22.4 in)
Modèles de bâtis compatibles Use with Model 336X (dual T-slot column cover style only), 446X*, 556X, 586X, and 596X dual column table top, standard width load frames only.

Protective Debris Shields 2910 Series

Test space enclosures or protective shields are sometimes a necessary safety accessory depending on the type of specimen being tested.

  • Produits
  • 11/27/2018
  • 0.7 MB

Sélecteur géographique

Dismiss Region Selector

Americas

  • North America
  • Brasil
  • South America

All Other Countries

  • Global Site

Europe

  • France
  • Deutschland
  • Italia
  • Polska
  • España
  • Türkçe
  • United Kingdom

Asia Pacific

  • 中国
  • India
  • 日本
  • 대한민국
  • 台灣
  • ประเทศไทย
Instron Logo White
INFORMATIONS DE CONTACT

3 boulevard Jean Moulin,
Omega Parc Bâtiment 2,
ELANCOURT, Cedex ,
78990, France

Ventes : +33 1 39 30 66 30

Maintenance : +33 1 39 30 66 31

LIENS UTILES
  • Systèmes d’essai
  • Logiciel
  • Accessoires d’essai
  • Catalogue
  • Glossaire
  • Bibliothèque
  • Solutions d’essai
  • Lettres d’information
  • Séminaires en ligne
  • Étude de cas
  • Événements
  • Carrières
Policies / Legal
  • Politique de confidentialité et de témoins de connexion
  • Conditions générales
  • Contrôle à l’export
  • Avis de données RGPD
ENTREZ EN CONTACT AVEC NOUS
INSCRIVEZ-VOUS À NOTRE LETTRE D’INFORMATION
ADRESSE ÉLECTRONIQUE
© Illinois Tool Works Inc. Tous droits réservés.
[email protected]
  • Politique de confidentialité et de témoins de connexion
  • Conditions générales
  • Contrôle à l’export
  • Avis de données RGPD